Stokamoto
Stokomoto
Vice Admiral
Posts:3728
 | | 29 Jul 2009 10:34 AM | | I want to waterproof my Spectrum Rx but how do you guys exactly go about waterproofing these RX. There are open slots on the sides and around exposing the circuit board.  | | | |
|
bb26
Rear Admiral (RDML)
Posts:1641
| | 29 Jul 2009 01:35 PM | | From what I saw in RI the receivers were housed in a waterproof box. | | | Just when you think you know the answers, I change the questions. | |
|
SnipeHunter
Commander
Posts:701
| | 29 Jul 2009 01:55 PM | | I put short extensions on each set of pins and then just fill plastic case with epoxy. Its easy to do and as long as you do a good job and cover every thing, get rid of air bubbles, etc its very reliable. | | | |
|
Iceman
Rear Admiral (RDML)
Posts:1186
| | 29 Jul 2009 03:31 PM | | Mine is in a block of wax but that will not work if you battle in warm climates. I would say scotchcote but that is hard to find and not getting easier. Epoxy works well. | | Rob A.
USS Alabama
USS Arizona
USS Saratoga
DKM Bismarck
USS John Brown
http://groups.yahoo.com/group/NYBG/ | |
|
Stokamoto
Stokomoto
Vice Admiral
Posts:3728
| | 29 Jul 2009 03:52 PM | | Would it be alright I wonder to seal the openings with tape, then add the extensions, then tool dip the recevior? | | | |
|
Kotori87
Rear Admiral (RADM)
Posts:2279
| | 29 Jul 2009 05:24 PM | | Tool dip is OK, but it's not as good as Skotchkote. I have had tool dip crumble and peel away from flexible surfaces like wires, making little gaps for water to get in through. Skotchkote is much better about that (although still not perfect). Another option is to spray down the circuitboard with Corrosion-X, then re-spray it after every sink. This works very well for receivers, although it gums up and slows down servos after the first 10 or so sinks.
The epoxy and wax ideas are very good, especially since you've got a 2.4ghz receiver that you don't need to change crystals on. Just be sure to treat the servo extensions with care, 'cause if they rust, they're not replaceable. | | | There are 101 different types of people: those who understand binary, those who don't, and those who just can't count... | |
|
SnipeHunter
Commander
Posts:701
| | 29 Jul 2009 06:03 PM | | Posted By Kotori87 on 29 Jul 2009 05:24 PM
... Just be sure to treat the servo extensions with care, 'cause if they rust, they're not replaceable.
Good point, I didnt mention that I replace all the servo plugs in my boat with the mini deans 3 prong connectors. Much higher quality and far fewer corrosion problems. More reliabilty is worth the added time and expense.
| | | |
|
Iceman
Rear Admiral (RDML)
Posts:1186
| | 29 Jul 2009 06:38 PM | | That is the good feature of the wax. I had a problem, melted it down, fixed it and recast it. | | Rob A.
USS Alabama
USS Arizona
USS Saratoga
DKM Bismarck
USS John Brown
http://groups.yahoo.com/group/NYBG/ | |
|
mabgfounder
Midshipman
Posts:32
| | 29 Jul 2009 06:45 PM | | Here is what I did for the one receiver I personally have waterproofed: - pop open the RX case
- paint the circuit board with clear nail polish. Its important not to paint the crystal in place (not an issue for you) or to paint over any of the servo pins
- I then tool dip the whole assembly (crystal included) except for the servo pins
- reassemble the case and install in boat
This has held up for almost ten years. The RX has only been submerged twice but it did not require any cleanup when pulled out of the water (worked right off the bat) I now have owned two ships with water tight boxes - Through them I have learned to hate water-tight boxes. They work great for a couple of years but eventually fail. Unfortunately they always seem to start leaking right after I start trusting them... I've sold one of the boats but on the other I pulled the top of the water tight box off. It keeps things dry until the boat sinks. It then makes a handy tub for soaking everything with alcohol. | | | |
|
Kotori87
Rear Admiral (RADM)
Posts:2279
| | 30 Jul 2009 04:28 AM | | Posted By mabgfounder on 29 Jul 2009 06:45 PM
I have learned to hate water-tight boxes. They work great for a couple of years but eventually fail. Unfortunately they always seem to start leaking right after I start trusting them... I've sold one of the boats but on the other I pulled the top of the water tight box off. It keeps things dry until the boat sinks. It then makes a handy tub for soaking everything with alcohol.
True, very true! watertight box = evil!
| | | There are 101 different types of people: those who understand binary, those who don't, and those who just can't count... | |
|
Stokamoto
Stokomoto
Vice Admiral
Posts:3728
| | 30 Jul 2009 08:46 AM | |  That sounds great . I will do as you suggest. I agree wt boxes are evil.That's why I waterproof the servos and RX then install them in thebox as backup incase the box leaks.
Thanks for the suggestions guys. | | | |
|
Ragresen
Lieutenant
Posts:333
| | 30 Jul 2009 08:47 AM | | Pry open the case and be rid of the sticky tape. Pour Epoxy into the bottom of case and set the Rx board into it. Be sure to tape off the pins with electrical tape ( Epoxy does not seem to stick to Electrical tape). Once the bottom is set then add more epoxy to the top of the board and then set the top cover in place. Let it all dry and then pull the tape from the pins.
I have had mine sit on the bottom at nats in 3 feet of water for an hour and no problems. | | Member MWC #285
Southeast Attack Squadron
SMS Kron Prinz Wilhelm (Battle Ready)
USS Des Moines (shipyards)
DKM Prinz Eugen (Keel Laid) | |
|
Iceman
Rear Admiral (RDML)
Posts:1186
| | 30 Jul 2009 10:14 AM | | I agree, I hate the water retaining boxes also. Even if you don't get wet in there, moisture can form due to sitting in the sun and water. | | Rob A.
USS Alabama
USS Arizona
USS Saratoga
DKM Bismarck
USS John Brown
http://groups.yahoo.com/group/NYBG/ | |
|
Stokamoto
Stokomoto
Vice Admiral
Posts:3728
| | 30 Jul 2009 12:21 PM | | I used to have an issue where my Mav-3 would vent excess gas into the box. Looked like my WT box was breathing. It would quickly tarnish all the brass in the box quickly. One thing I haged about the box is quick access. I hated breaking seals to get inside. I generally don't use wt boxes anymore but some cases like my Bismarck it works out ok. | | | |
|
Stokamoto
Stokomoto
Vice Admiral
Posts:3728
| | 30 Jul 2009 12:28 PM | | Ok will do. This is great help guys Tks. I am new to this Technology so I don't want to screw it up. | | | |
|
wrenow
Lieutenant
Posts:311
| | 31 Jul 2009 12:29 AM | | Tooldip and Liquid Electrical Tape delaminate over time and foster corrosion.
Epoxy is permanent if applies right, but makes repairs difficult if even possible.
3MScotchkote is the common waterproofing agent of choice (yes, there ore some special silicone based conformal coatings available for electronics, and some exotic technologies, but....)
Scotchkote is simple, reliable, and holds up well over time. I have receivers that have been going on 7 years of combat without problems.
Cheers, | | Wreno
NTXBG
USS Lake Shore
USS Reluctant
USS Nathanial Greene
Dunkerque
| |
|
Stokamoto
Stokomoto
Vice Admiral
Posts:3728
| | 31 Jul 2009 11:20 AM | | Where do I get this Scotchkote? | | | |
|
Kotori87
Rear Admiral (RADM)
Posts:2279
| | 31 Jul 2009 02:11 PM | | Lowes carries it, at least in California. Not sure about other places, though. | | | There are 101 different types of people: those who understand binary, those who don't, and those who just can't count... | |
|
Iceman
Rear Admiral (RDML)
Posts:1186
| | 01 Aug 2009 01:44 AM | | Lowes stopped carrying it in NY but here is the manufacture link http://solutions.3m.com/wps/portal/3M/en_US/3MElectrical/Home/ProductsServices/Products/?PC_7_RJH9U5230GE3E02LECIE20OES1_nid=6Q3BGBPJ7CbeFR7R0D83TCgl | | Rob A.
USS Alabama
USS Arizona
USS Saratoga
DKM Bismarck
USS John Brown
http://groups.yahoo.com/group/NYBG/ | |
|
Nick
Veteran
Rear Admiral (RDML)
Posts:1051
| |